New Profile Posts

  1. Razar
    Razar
    Hoping someone make the guide how to enable MBL some time.. ABL and I are not friends.
    1. cez
      cez
      I changed firmware
      Jan 17, 2017 at 8:32 PM
      Razar likes this.
  2. Syko_Symatic
    Syko_Symatic
    Duet Wifi Ordered!!
    1. T3P3Tony likes this.
    2. cez
      cez
      Where from? is it easy to upgrade the existing board?
      Jan 17, 2017 at 5:52 PM
    3. Syko_Symatic
      Syko_Symatic
      Duet3d and yes it's pretty much plug and play. They have a good wiki if you want to read through it.
      Jan 17, 2017 at 9:35 PM
  3. Ephemeris
    Ephemeris
    “Don’t tug on that. You never know what it might be attached to.”
  4. Ephemeris
    Ephemeris
    “Don’t tug on that; you never know what it might be attached to."
  5. Thomas Kamsker
    Thomas Kamsker
    Build finnished quite happy broke IR Mount ;=-
  6. Syko_Symatic
    Syko_Symatic
    Starting to print my UM2 Extended clone!
  7. 3DDP
    3DDP
    AVR DUDE ERROR
  8. 3DDP
    3DDP
    No suitable baud rate found.
  9. TimV
    TimV
    oYes, printing 2.85 on BB, near zero modification :)
  10. 3DDP
    3DDP
    windows displays a code 10 for rumba & only sees to install drivers using legacy hardware option, drivers are up to date. iOS says no device
  11. AndyVirus
    AndyVirus
    Success! Migrated from IDEX Rumba to IDEX DuetWifi (though awaiting DueX5 board)
  12. 3DDP
    3DDP
    Working on trying to establish a USB connection from Rumba to ANY computer, Windows or iOS... No luck...
    1. W1EBR.Gene
      W1EBR.Gene
      Have you been successful yet?
      Dec 18, 2016
    2. 3DDP
      3DDP
      No. It only writes via programmer, which doesn't upload anything and displays a USB Port that is not found or seen by the computer. the software using to write the firmware doesn't even see the port.
      Dec 19, 2016
  13. Razar
    Razar
    Volcano up and running, time to finally print BIG.
  14. fpex
    fpex
    Pause from 3D, time for PS-VR :-)
  15. fpex
    fpex
    First print with nGen Flex on BB
  16. fpex
    fpex
    I Can confirm, lei plate red works way better than. Blue.
  17. Razar
    Razar
    Replaced the 24V fan with a 12 V fan. This is a worthwhile upgrade since its so much more quiet.
  18. Spoon Unit
    Spoon Unit
    socks !
    1. Duncan Chivers likes this.
  19. mike01hu
    mike01hu
  20. Atilla BAYKAL
    Atilla BAYKAL mike01hu
    Hi Dear,
    I buy genunie e3d v6 Bowden Hotend 3mm. But i make a mistake i will be buy 1.75. My question can i convert 3 mm to 1.75?
    If it doesn't possible if i buy "v6 HotEnd Metal Parts Only - 1.75mm Universal" is that enough?

    Thanks for helping, best regards.
    1. Michael Frampton
      Michael Frampton
      We have a hybrid dual bb1.1 with both 1.75mm and 3mm nozzles on .
      Sep 18, 2016