Recent Activity

Activity stream for all registered members at E3D BigBox Forum.

  1. Julian64 posted a new thread.

    Titan aero upgrade kit

    does the titan aero upgrade kit come with a bracket? There doesn't seem to be an obvious list of parts for the upgrade kit

    Forum: General

    Mar 26, 2017 at 11:35 AM
  2. Pipshag replied to the thread IN DEVELOPMENT BigBox Dual X-Carriages (Bowden).

    Has anyone built this and have a S3D profile to share for PLA? I can't seem to get good retraction settings, no matter what I do. If you...

    Mar 26, 2017 at 11:14 AM
  3. R Design replied to the thread Stegosaurus.

    Zoomed in on the build cost in the Simplify screnshot: I suppose most of that reflects the true cost of Scaffold? Imagine the time and...

    Mar 26, 2017 at 10:36 AM
  4. R Design replied to the thread COMPLETE Cheap detachable enclosure case for BigBox.

    Really nice job. Out of interest, what was the approx material cost? I've heard of some people using computer server cabinets as lazy...

    Mar 26, 2017 at 10:31 AM
  5. R Design liked Rob Heinzonly's post in the thread COMPLETE Cheap detachable enclosure case for BigBox.

    Last weeks I've been building a case that keeps my BigBox printer warm during winter time prints, and while doing prints that are prone...

    Mar 26, 2017 at 10:28 AM
  6. Folkert Kaman attached a file to the thread IN DEVELOPMENT Chase's dual direct titan idex conversion.

    Ok, so here is my solution. It consists of a modified extruder carrier and a part to be glued on top to hold the 10 pin Molex connector...

    Photo-2017-03-26-10-43-38_0528.JPG Photo-2017-03-26-10-32-58_0525.JPG Photo-2017-03-26-10-33-20_0526.JPG Photo-2017-03-26-10-33-48_0527.JPG Mar 26, 2017 at 9:52 AM
  7. potti5 liked Greg Holloway's post in the thread Stegosaurus.

    I have printed a Stegosaurus for a friend (https://www.thingiverse.com/thing:133660). It has been printed with Glow-In-The-Dark PLA and...

    2017-03-24 15.26.29.jpg 2017-03-24 17.19.19.jpg 2017-03-25 10.18.09.jpg 2017-03-25 10.19.48.jpg 2017-03-25 10.20.29.jpg 2017-03-25 10.21.14.jpg 2017-03-25 10.21.57.jpg 2017-03-25 10.22.51.jpg 2017-03-25 10.22.56.jpg 2017-03-25 10.23.33.jpg 2017-03-25 10.24.51.jpg 2017-03-25 10.36.03.jpg 2017-03-25 10.36.09.jpg 2017-03-25 10.52.36.jpg s3d_layers.jpg s3d_sliced.jpg s3d_supports.jpg grass.jpg Mar 26, 2017 at 9:03 AM
  8. Kanedias replied to the thread Ultimaker 2 upgrade kit not functioning.

    You could try sending a PM to Dan Halsall if you're not getting a response from support....

    Mar 26, 2017 at 8:38 AM
  9. Mike Kelly replied to the thread Severely Deformed 3D Benchy.

    It looks to me like a 200 step/rev is being used on the Y axis instead of a 400 step/rev, but it may just be the perspective

    Mar 26, 2017 at 6:50 AM
  10. Anjin Meili replied to the thread Ultimaker 2 upgrade kit not functioning.

    any updates? my kits also does not work at all.

    Mar 26, 2017 at 6:23 AM
  11. Anjin Meili replied to the thread Ultimaker 2 Titan + e3d upgrade kit... Issues with Extruder.

    yes, i am using the bowden extruder as shipped. i have heard nothing from e3d yet either.

    Mar 26, 2017 at 6:22 AM
  12. Pixelnate replied to the thread Inconsistent Z ribbing/Banding.

    Did you ever get this resolved? I am having similar issues with a Titan + E3Dv6.

    Mar 26, 2017 at 4:19 AM
  13. Mike Kelly liked Greg Holloway's post in the thread Stegosaurus.

    I have printed a Stegosaurus for a friend (https://www.thingiverse.com/thing:133660). It has been printed with Glow-In-The-Dark PLA and...

    2017-03-24 15.26.29.jpg 2017-03-24 17.19.19.jpg 2017-03-25 10.18.09.jpg 2017-03-25 10.19.48.jpg 2017-03-25 10.20.29.jpg 2017-03-25 10.21.14.jpg 2017-03-25 10.21.57.jpg 2017-03-25 10.22.51.jpg 2017-03-25 10.22.56.jpg 2017-03-25 10.23.33.jpg 2017-03-25 10.24.51.jpg 2017-03-25 10.36.03.jpg 2017-03-25 10.36.09.jpg 2017-03-25 10.52.36.jpg s3d_layers.jpg s3d_sliced.jpg s3d_supports.jpg grass.jpg Mar 26, 2017 at 12:42 AM
  14. Grigori set their occupation to Programming.

    Mar 25, 2017 at 10:04 PM
  15. Grigori set their location as Tallinn, Estonia.

    Mar 25, 2017 at 10:04 PM
Loading...