Recent Content by mhe

  1. mhe
    Post

    glass bed vs. e.g. BuildTak flex plate

    Clever3D PEI plate, E3D glass plate blank and an E3D glass plate covered with PrintBite+ foil. Haven't missed a flexible plate yet.
    Post by: mhe, Jan 20, 2020 in forum: Getting Started
  2. mhe
    Post

    Z-dragchain vs. printed Z-axis cover

    Couldn't we move the motor cable to the other side and mirror the cover? Then these two couldn't interfere to begin with.
    Post by: mhe, Jan 20, 2020 in forum: Motion System
  3. mhe
    Post

    E3D hemera chewing through filament

    This should work brilliantly. I run 0.3mm distance at 30mm/s and 0.1mm coasting in S3D. Approaching insane quality, the Hemera after just a few...
    Post by: mhe, Jan 20, 2020 in forum: Troubleshooting
  4. mhe
    Post

    Spare rear panel?

    You're most welcome, that's what a community is for! :)
    Post by: mhe, Jan 20, 2020 in forum: Getting Started
  5. mhe
    Post

    hotend can rotate is it normal

    Do you mean the small heater block below the heatsink?
    Post by: mhe, Jan 20, 2020 in forum: Titan
  6. mhe
    Post

    tool offsets for new tools

    I believe they are relative to the probe switch that does the z-homing and bed probing. My approach always was to get the tool pickup to work,...
    Post by: mhe, Jan 20, 2020 in forum: Tool heads & ToolChanger
  7. mhe
    Post

    tool offsets for new tools

    In your config.g, look for these lines fairly at the bottom of your fille: ;tool offsets G10 P0 X-9 Y39 Z-4.65 ; T0 G10 P1...
    Post by: mhe, Jan 20, 2020 in forum: Tool heads & ToolChanger
  8. mhe
    Post

    Spare rear panel?

    https://github.com/e3donline/Motion-System The panels are in the DXF folder, for laser and waterjetting, these should do. If you need to machine...
    Post by: mhe, Jan 20, 2020 in forum: Getting Started
  9. mhe
    Post

    Setup V6 thermistor on Duet

    Glad to hear that, happy printing!
    Post by: mhe, Jan 20, 2020 in forum: Tool heads & ToolChanger
  10. mhe
    Post

    Setup V6 thermistor on Duet

    https://e3d-online.dozuki.com/Guide/V6+RepRap+Firmware+Configuration/26?lang=en...
    Post by: mhe, Jan 20, 2020 in forum: Tool heads & ToolChanger
  11. mhe
    Post

    Grease for tool head assembly

    White lithium works well for me so far.
    Post by: mhe, Jan 18, 2020 in forum: Tool heads & ToolChanger
  12. mhe
    Post

    Revising the toolchanger to hold a 2.2kw milling spindle

    I dont' believe it is a good idea to change tools that way, especially not with a spindle like that - you can easily cut aluminium with it,...
    Post by: mhe, Jan 17, 2020 in forum: Tool heads & ToolChanger
  13. mhe
    Profile Post

    Enjoying Hemera on the TC, it is simply wonderful

    Enjoying Hemera on the TC, it is simply wonderful
    Status Update by mhe, Jan 17, 2020
  14. mhe
    Post

    Adding a tool loaded detection switch

    Instead of putting something in the toolhead, wouldn't it be easier to check for tool presence by having a switch in each dock and check there? If...
    Post by: mhe, Jan 17, 2020 in forum: Tool heads & ToolChanger
  15. mhe
    Post

    Hemera Stops Extruding

    I haven't printed anything big/long yet, but I did PLA, PLA/PHA, XT-CF20 and PETG/EDGE with it so far, no problems whatsoever. PLA I run at 205°C...
    Post by: mhe, Jan 17, 2020 in forum: Troubleshooting