Recent Content by Pipshag

  1. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    I noticed I didn't put any clips for keeping the Bowden collet stretched up and got some movement in the ptfe tube. Printed some clips and fitted...
    Post by: Pipshag, Mar 26, 2017 in forum: Guides, Mods, and Upgrades
  2. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    Has anyone built this and have a S3D profile to share for PLA? I can't seem to get good retraction settings, no matter what I do. If you share...
    Post by: Pipshag, Mar 26, 2017 in forum: Guides, Mods, and Upgrades
  3. Pipshag
    Post

    SOLVED Duet Wifi BLTouch setup (for BigBox)

    Marlin does this as well with #define AUTO_BED_LEVELING_BILINEAR. It can also synthesize intermediate points for more detailed grid.
    Post by: Pipshag, Mar 17, 2017 in forum: Calibration, Help, and Troubleshooting
  4. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    Did anyone else notice stepper whine on the NEMA11 motors when they're turned on? Unsure if that's something I can make something about. As...
    Post by: Pipshag, Mar 8, 2017 in forum: Guides, Mods, and Upgrades
  5. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    And I think with that I will be able to complete a successful print later today! I am very grateful for you help and continued dedication to the...
    Post by: Pipshag, Feb 26, 2017 in forum: Guides, Mods, and Upgrades
  6. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    Thank you for that very well written guide. It makes it much more clearer now. My last question is about MBL. You run it for T0, right? It doesn't...
    Post by: Pipshag, Feb 26, 2017 in forum: Guides, Mods, and Upgrades
  7. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    I'm very sorry @Greg Holloway but I really can't figure out the correct way to do it. My T1 is lower and no matter how I configure the firmware,...
    Post by: Pipshag, Feb 25, 2017 in forum: Guides, Mods, and Upgrades
  8. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    That was easy! :D Everything is installed, firmware adjusted and flashed. I went through the threads available in a hope to understand how to set...
    Post by: Pipshag, Feb 25, 2017 in forum: Guides, Mods, and Upgrades
  9. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    Installed everything but the cooling fans and when testing the motion system I notice that the nozzles hit the platform plastic. It seems I can't...
    Post by: Pipshag, Feb 23, 2017 in forum: Guides, Mods, and Upgrades
  10. Pipshag
    Post

    IN DEVELOPMENT Titan Dual Direct Drive Design

    I think I read something about a bug in RCBugFix which was fixed at a later date. Not 100% sure though. You could pull in the new changes and...
    Post by: Pipshag, Feb 21, 2017 in forum: Guides, Mods, and Upgrades
  11. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    So, I've got almost everything and started doing the cabling. I've ordered the 11HS20-0674S steppers, which don't have a contact but loose cables...
    Post by: Pipshag, Feb 20, 2017 in forum: Guides, Mods, and Upgrades
  12. Pipshag
    Post

    IN DEVELOPMENT Titan Dual Direct Drive Design

    240 has been working good for me, it's from the front of the BigBox to the back of the dump zone. Did you adjust your front endstop screw?
    Post by: Pipshag, Feb 17, 2017 in forum: Guides, Mods, and Upgrades
  13. Pipshag
    Post

    IN DEVELOPMENT Titan Dual Direct Drive Design

    Yeah, there was some changes which made LIN_ADVANCE work... not satisfying. Currently abadoned any RCBugFix in favour of a coming IDEX Bowden update.
    Post by: Pipshag, Feb 15, 2017 in forum: Guides, Mods, and Upgrades
  14. Pipshag
    Post

    IDEAS Trinamic TMC2100 - quieter (and better) stepper drivers (?)

    Thanks for the idea and all the information you wrote down. I just installed and fixed the last on my BigBox so I'll add this for future...
    Post by: Pipshag, Feb 14, 2017 in forum: Guides, Mods, and Upgrades
  15. Pipshag
    Post

    IN DEVELOPMENT BigBox Dual X-Carriages (Bowden)

    Thanks for all the information given so far. I'm happy to say I've got the components ordered and just started printing the parts. Looking forward...
    Post by: Pipshag, Feb 10, 2017 in forum: Guides, Mods, and Upgrades