Recent Content by smoki3

  1. smoki3
    Thread

    Tool Calibration Station

    Hi together, I have designed a tool calibration station. It is equiped with a raspberry pi zero/camera and a hight sensor (guided platform which...
    Thread by: smoki3, Feb 18, 2020 at 8:09 PM, 0 replies, in forum: Tool heads & ToolChanger
  2. smoki3
    Post

    Tool Head Dreams

    Tried it today in the chat. They told me that it is not sold separately
    Post by: smoki3, Jan 27, 2020 in forum: Tool heads & ToolChanger
  3. smoki3
    Post

    Bedleveling Deviation

    This is also the way I have leveled my bed :) To e3d's defense, I don't have a metal Z-NUT-BRACKET. I printed it from carbon fiber reinforced...
    Post by: smoki3, Jan 27, 2020 in forum: Motion System
  4. smoki3
    Thread

    Bedleveling Deviation

    Hi, I want to know what are your maximum deviation after bed leveling? As the cantilever tend to be a bit lower in the front part of the build...
    Thread by: smoki3, Jan 27, 2020, 5 replies, in forum: Motion System
  5. smoki3
    Post

    Tool Head Dreams

    Where can you by the reveiver and the docks?
    Post by: smoki3, Jan 27, 2020 in forum: Tool heads & ToolChanger
  6. smoki3
    Post

    Z-dragchain vs. printed Z-axis cover

    yes this would be the easiest way. I will do the cut out also on the other side in the elec panel. And will turn the z motor. The other cut out I...
    Post by: smoki3, Jan 22, 2020 in forum: Motion System
  7. smoki3
    Post

    ToolChanger profile for Cura?

    Yes had the same issue with cura. The put a M109 before Homing. And I never got it running nice with the duet. Always had to manually edit the...
    Post by: smoki3, Jan 18, 2020 in forum: Getting Started
  8. smoki3
    Post

    Stall detection configuration

    @Greg Holloway I pushed a pull request on github. This should fix this. I also saw that you merged something about the fan control. I also pushed...
    Post by: smoki3, Jan 17, 2020 in forum: Motion System
  9. smoki3
    Post

    From RRF2 to RRF3 on Duet2 WiFI

    I uploaded my config here: https://github.com/smoki3/RepRapFirmware-SD
    Post by: smoki3, Jan 17, 2020 in forum: Getting Started
  10. smoki3
    Post

    DIY Motion System and Tool Changer

    @p3t3rp4nd4 Do you get heating issues on the duet? I never needed active cooling. May you can simply use small heatsink on the motor drivers.
    Post by: smoki3, Jan 16, 2020 in forum: Motion System
  11. smoki3
    Post

    Adding a tool loaded detection switch

    I think the most useful cases are to prevent homing with a tool and check if the tool change is successful. Technically I would recommend to...
    Post by: smoki3, Jan 16, 2020 in forum: Tool heads & ToolChanger
  12. smoki3
    Post

    Stall detection configuration

    Yes it doesn't make sense
    Post by: smoki3, Jan 16, 2020 in forum: Motion System
  13. smoki3
    Post

    Un expected move when changing tools

    I already have adjusted the config for RRF 3.0 you can find it here: https://github.com/smoki3/RepRapFirmware-SD
    Post by: smoki3, Jan 16, 2020 in forum: Motion System