Recent Activity

Activity stream for all registered members at E3D BigBox Forum.

  1. Ed Kirk posted a new thread.

    Use Titan Aqua as a Bowden extruder

    I found this adapter that will screw into the bottom of the Titan Aqua for use as a Bowden extruder. Seems to be working extremely...

    Forum: General

    Aug 16, 2018 at 12:37 AM
  2. Spoon Unit replied to the thread Z Seam Gap 0,8mm Nozzle.

    I was playing with the same issue using a 1mm volcano nozzle. I see similar results. Ultimately it's down to tuning retraction to get...

    Aug 15, 2018 at 10:29 PM
  3. jfb replied to the thread IDEAS Original BigBox upgrade feedback.

    Mine were ok - I've had no issues. You *can* straighten them yourself, as with any other lead screw, but it's a pain to do and I'd...

    Aug 15, 2018 at 9:16 PM
  4. jfb replied to the thread IDEAS Original BigBox upgrade feedback.

    I'd actually forgotten about the lazy susan - yes it's really useful. I'd also add Alex's adaptors for bigger spools...

    Aug 15, 2018 at 9:13 PM
  5. Peter85 posted a new thread.

    Z Seam Gap 0,8mm Nozzle

    Hi all, I have some issues with my Titan Aero Volcano setup with. Currently i try optimize the quality of my printer. But I can´t...

    IMG_20180815_213204.jpg

    Forum: Volcano

    Aug 15, 2018 at 8:55 PM
  6. Miasmictruth replied to the thread ToolChanging Extruded Aluminum E3D BB3D2?.

    I am sure there you wont want to answer this but any rough ideas on timeline, even vague like before the end of the year, next year...

    Aug 15, 2018 at 8:48 PM
  7. hevilp posted a new thread.

    Chimera+ Aqua

    Hi, how is temperature of the heatsink (the water reservoir) when the watercooling is running? If I heat up to 220°C I cannot touch...

    Forum: Multi-Extrusion

    Aug 15, 2018 at 6:48 PM
  8. Karel replied to the thread Extruder motors stopped during print.

    Yes, I saw the schematics, did some test and came to the conclusion that the rumba is beyond repair. So I will replace it with a Duet...

    Aug 15, 2018 at 3:51 PM
  9. sebastiaan replied to the thread IDEAS Original BigBox upgrade feedback.

    Thanks for all the ideas and feedback! You all do love the Duet :D Is it that much better than a Rumba with updated Marlin firmware and...

    Aug 15, 2018 at 3:46 PM
  10. Spoon Unit replied to the thread Volcano settings? Blobs/lines of under extrusion.

    Sure. It's far from a perfect result, but I think it's basically down to retraction tuning, or just physics with a volcano nozzle. I...

    Aug 15, 2018 at 3:10 PM
  11. Old_Tafr replied to the thread Volcano settings? Blobs/lines of under extrusion.

    Could you post your S3D config file so that I can compare all the settings from my numerous (failed) attempts?

    Aug 15, 2018 at 9:39 AM
  12. Old_Tafr liked Spoon Unit's post in the thread Volcano settings? Blobs/lines of under extrusion.

    I thought I'd take on the volcano Benchy challenge. Lots to praise and some slicer/firmware shortcoming are, I think revealed, or I may...

    Aug 15, 2018 at 9:38 AM
  13. Old_Tafr replied to the thread IDEAS Original BigBox upgrade feedback.

    I can't really add to the list, but what I found really useful was to mount the BigBox on a Lazy Susan. I found the need to access the...

    Aug 15, 2018 at 9:36 AM
  14. Old_Tafr liked Rob Heinzonly's post in the thread IDEAS Original BigBox upgrade feedback.

    If you are going to do an upgrade, step one should be: take a Duet. Step two and three: take a Duet ;). Superior bed levelling, fast and...

    Aug 15, 2018 at 9:29 AM
  15. Rob Heinzonly replied to the thread IDEAS Original BigBox upgrade feedback.

    I forgot about that one, Clever3D is indeed second best after Duet. Print ... cool down ... pick up ... and print again. No more messing...

    Aug 15, 2018 at 7:28 AM
Loading...