Extruder Heatsink in the X-Carriage

Discussion in 'BigBox General Chat' started by Irawan Tri Kusumo, Mar 21, 2016.

  1. Irawan Tri Kusumo

    Irawan Tri Kusumo Well-Known Member

    Joined:
    Sep 5, 2015
    Messages:
    116
    Likes Received:
    21

    Attached Files:

    #1 Irawan Tri Kusumo, Mar 21, 2016
  2. Rob Heinzonly

    Rob Heinzonly Well-Known Member

    Joined:
    Sep 20, 2015
    Messages:
    406
    Likes Received:
    145
    Did you place the rubber ring in the enclosing first ?
     
    #2 Rob Heinzonly, Mar 21, 2016
  3. Irawan Tri Kusumo

    Irawan Tri Kusumo Well-Known Member

    Joined:
    Sep 5, 2015
    Messages:
    116
    Likes Received:
    21
    Yes. I did.
     
    #3 Irawan Tri Kusumo, Mar 21, 2016
  4. Rob Heinzonly

    Rob Heinzonly Well-Known Member

    Joined:
    Sep 20, 2015
    Messages:
    406
    Likes Received:
    145
    Hmm. They indeed look a little to deep, unfortunately I'm at work now. So I can't compare it with my machine.
     
    #4 Rob Heinzonly, Mar 21, 2016
  5. Irawan Tri Kusumo

    Irawan Tri Kusumo Well-Known Member

    Joined:
    Sep 5, 2015
    Messages:
    116
    Likes Received:
    21
    Thanks @Rob Heinzonly . I am wondering what could be gone wrong when it is too deep.
     
    #5 Irawan Tri Kusumo, Mar 21, 2016
  6. K3LAG

    K3LAG Well-Known Member

    Joined:
    Oct 9, 2015
    Messages:
    55
    Likes Received:
    31
    Mine fit about the same as you show in your picture.
     
    #6 K3LAG, Mar 21, 2016
  7. Irawan Tri Kusumo

    Irawan Tri Kusumo Well-Known Member

    Joined:
    Sep 5, 2015
    Messages:
    116
    Likes Received:
    21
    @K3LAG, so is yours working fine ?
     
    #7 Irawan Tri Kusumo, Mar 21, 2016
  8. PsyVision

    PsyVision Moderator
    Staff Member

    Joined:
    Sep 4, 2015
    Messages:
    798
    Likes Received:
    248
    Mine fit the same and work fine.
     
    #8 PsyVision, Mar 21, 2016
  9. Irawan Tri Kusumo

    Irawan Tri Kusumo Well-Known Member

    Joined:
    Sep 5, 2015
    Messages:
    116
    Likes Received:
    21
    Good, thanks all for the info. Because I printed again the part using ColorFabb XT, I worry the size does not fit properly. Also I printed the alternative model.
     
    #9 Irawan Tri Kusumo, Mar 21, 2016
  10. PsyVision

    PsyVision Moderator
    Staff Member

    Joined:
    Sep 4, 2015
    Messages:
    798
    Likes Received:
    248
    As long as it doesn't wobble when the grub screws have tightened then its fine.
     
    #10 PsyVision, Mar 21, 2016
  11. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 7, 2014
    Messages:
    449
    Likes Received:
    92
    Yeah don't worry if it's too deep, better than too shallow
     
    #11 Mike Kelly, Mar 25, 2016
(You must log in or sign up to post here.)

Share This Page